The example above was taken from an Aruba 5412R zl2 (KB.) equipped with with four PS modules and no PoE PD connected. HWMonitor has had 0 updates within the past 6 months. Refer to command's help option for field definitions Download HWMonitor for Windows to monitor the main health sensors of your PC, such as temperature, voltages, and fan speed. Status and Counters - Power Supply Detailed Informationġ J9829A CN6AK36XXX Powered AC Power Consumption : 81 WattsĢ J9829A CN6AK36XXX Powered AC Power Consumption : 84 Wattsģ J9829A CN6AK36XXX Powered AC Power Consumption : 82 WattsĤ J9829A CN6AK36XXX Powered AC Power Consumption : 88 WattsĬurrently supplying 258 W / 4400 W total power. The program handles : CPU and GPU-level hardware monitoring LPCIO chips with monitoring features (ITE IT87 series, Winbond and Nuvoton ICs) memory modules with thermal sensors SSD / hard disks via S.M.A.R.T. Try with the show system power-supply detailed CLI command.ĥ412Rzl2# show system power-supply detailed HWMonitor is a hardware monitoring program that reads PC systems main health sensors : voltages, temperatures, powers, currents, fans speed, utilizations, clock speeds. Is there a command to see the temperature of the PSU's? What are their threshholds set at? The switch has 2 x J9829A PSU's and the power consumption is rather low compared to the 1100 W they can deliver.Ī HP J9538A 8p 10G-GbE SFP+ v2 zl Module 32 WĮ HP J9538A 8p 10G-GbE SFP+ v2 zl Module 30 Wį HP J9538A 8p 10G-GbE SFP+ v2 zl Module 31 W However, some users with HP ProLiant servers may encounter down Active Monitors immediately after assigning them to the ProLiant servers. These monitors provide support for some HP ProLiant servers out-of-the-box. However, I seem to be unable to find other temperature commands in the switch than the general command: WhatsUpGold is supplied with built-in Power Supply, Fan, and Temperature Active monitors. The error I have a question about is it exceeds the temperature threshold value. In the current era of supply chain challenges, tossing drugs is more than a. M 04/23/20 11:36:42 02794 chassis: AM1: Internal power supply 2: PoE power within the temperature threshold value. Consolidates all wireless monitoring: sound, temperature, power, humidity. M 04/23/20 11:35:42 02798 chassis: AM1: Internal power supply 2 main PoE power faulted. M 04/2 3/20 11:35:42 02794 chassis: AM1: Internal power supply 2: PoE power exceeds the temperature threshold value. If a sensor needs to be re-installed it is recommended to use this type of adhesive.I have several Aruba 5406R-zl2's in production that from time to time have error messages as those below: The sensors use 3M type 93020LE adhesive. What kind of adhesive is used on the BTM sensor? Some are identified easily, gpu and cpu for example, while others are not. It displays temperature readings on start. The power consumption is 1.2W regardless of how many sensors are connected. Speedfan is a temperature monitor that can also be used to change the speed of system fans manually or automatically based on the system's temperature. What is the power consumption of the BTM? Ratings are 7A at 240VAC and 10A at 120VAC. Should a fault occur in the probe circuit or should the po- wer supply be interrupted, an auxiliary relay in the power supply unit will drop out. The BTM has (2) SPDT volt-free contact relays. What are the communication options for the BTM? The system has been tested with a total loop length of 122 m (400 ft.) and the system operated normally. If the lengths become to excessive then there may be a possibility that the 4+ warning may activate with 3+ over-temperature faults. From an electronic point of view there is no reason why the length cannot be greater than 30 m (100 ft.). What are the maximum cable lengths for the BTM system?Īt this time there is not a concrete limit on the total cable loop length or the length of cable between sensors. The BTM is a fixed temperature device, so the temperature selected is above the normal swings in operating temperature but low enough to ensure that a battery that is overheating can be identified before thermal runaway occurs. If the battery is operating at 18✯ (10✬) above that, it is a candidate for thermal runaway. The nominal operating temperature for batteries is generally considered to be 77✯ (25✬). Why is the temperature threshold for alarming set to 95✯ (35✬)? Ensure that energy running to assets meets specification. Total Harmonic Distortion (THD) is a key indicator of potential power problems. If there are more than 14 sensors in over-temperature then the LED’s on the sensors become so dim that they are not visible, however the 1+ and 4+ indicators and relays on the monitor are still active. Of equal importance to energy consumption is the quality of power being consumed and the effect on equipment and operations. The maximum number of sensors for each monitor is approximately 200. What is the maximum number of sensors that can be connected to a single monitor?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |